This documentation is for version 2.1.0-rc2. Other versions.

Table of contents

Adafruit HUZZAH ESP8266 (ESP-12)

TODO: add notes

NodeMCU 0.9

Pin mapping

Pin numbers written on the board itself do not correspond to ESP8266 GPIO pin numbers. Constants are defined to make using this board easier:

static const uint8_t D0   = 16;
static const uint8_t D1   = 5;
static const uint8_t D2   = 4;
static const uint8_t D3   = 0;
static const uint8_t D4   = 2;
static const uint8_t D5   = 14;
static const uint8_t D6   = 12;
static const uint8_t D7   = 13;
static const uint8_t D8   = 15;
static const uint8_t D9   = 3;
static const uint8_t D10  = 1;

If you want to use NodeMCU pin 5, use D5 for pin number, and it will be translated to 'real' GPIO pin 14.

NodeMCU 1.0

This module is sold under many names for around $6.50 on AliExpress and it's one of the cheapest, fully integrated ESP8266 solutions.

It's an open hardware design with an ESP-12E core and 4 MB of SPI flash.

Acording to the manufacturer, "with a micro USB cable, you can connect NodeMCU devkit to your laptop and flash it without any trouble". This is more or less true: the board comes with a CP2102 onboard USB to serial adapter which just works, well, the majority of the time. Sometimes flashing fails and you have to reset the board by holding down FLASH + RST, then releasing FLASH, then releasing RST. This forces the CP2102 device to power cycle and to be re-numbered by Linux.

The board also features a NCP1117 voltage regulator, a blue LED on GPIO16 and a 220k/100k Ohm voltage divider on the ADC input pin.

Full pinout and PDF schematics can be found here

Olimex MOD-WIFI-ESP8266-DEV

This board comes with 2 MB of SPI flash and optional accessories (e.g. evaluation board ESP8266-EVB or BAT-BOX for batteries).

The basic module has three solder jumpers that allow you to switch the operating mode between SDIO, UART and FLASH.

The board is shipped for FLASH operation mode, with jumpers TD0JP=0, IO0JP=1, IO2JP=1.

Since jumper IO0JP is tied to GPIO0, which is PIN 21, you'll have to ground it before programming with a USB to serial adapter and reset the board by power cycling it.

UART pins for programming and serial I/O are GPIO1 (TXD, pin 3) and GPIO3 (RXD, pin 4).

Get the board schematics here

Olimex MOD-WIFI-ESP8266

This is a stripped down version of the above. Behaves identically in terms of jumpers but has less pins readily available for I/O. Still 2 MB of SPI flash.

SparkFun ESP8266 Thing

Product page: https://www.sparkfun.com/products/13231

TODO: add notes

SweetPea ESP-210

TODO: add notes

ESPino

ESPino integrates the ESP-12 module with a 3.3v regulator, CP2104 USB-Serial bridge and a micro USB connector for easy programming. It is designed for fitting in a breadboard and has an RGB Led and two buttons for easy prototyping.

For more information about the hardware, pinout diagram and programming procedures, please see the datasheet.

Product page: http://www.espino.io/en

WifInfo

WifInfo integrates the ESP-12 or ESP-07+Ext antenna module with a 3.3v regulator and the hardware to be able to measure French telemetry issue from ERDF powering meter serial output. It has a USB connector for powering, an RGB WS2812 Led, 4 pins I2C connector to fit OLED or sensor, and two buttons + FTDI connector and auto reset feature.

For more information, please see WifInfo related blog entries, github and community forum.

Generic ESP8266 modules

These modules come in different form factors and pinouts. See the page at ESP8266 community wiki for more info: ESP8266 Module Family.

Usually these modules have no bootstapping resistors on board, insufficient decoupling capacitors, no voltage regulator, no reset circuit, and no USB-serial adapter. This makes using them somewhat tricky, compared to development boards which add these features.

In order to use these modules, make sure to observe the following:

Serial Adapter

There are many different USB to Serial adapters / boards. To be able to put ESP8266 into bootloader mode using serial handshaking lines, you need the adapter which breaks out RTS and DTR outputs. CTS and DSR are not useful for upload (they are inputs). Make sure the adapter can work with 3.3V IO voltage: it should have a jumper or a switch to select between 5V and 3.3V, or be marked as 3.3V only.

Adapters based around the following ICs should work:

PL2303-based adapters are known not to work on Mac OS X. See https://github.com/igrr/esptool-ck/issues/9 for more info.

Minimal Hardware Setup for Bootloading and Usage

PIN Resistor Serial Adapter
VCC VCC (3.3V)
GND GND
TX or GPIO2* RX
RX TX
GPIO0 PullUp DTR
Reset* PullUp RTS
GPIO15* PullDown
CH_PD PullUp

ESP to Serial

ESP to Serial

Minimal Hardware Setup for Bootloading only

ESPxx Hardware

PIN Resistor Serial Adapter
VCC VCC (3.3V)
GND GND
TX or GPIO2 RX
RX TX
GPIO0 GND
Reset RTS*
GPIO15 PullDown
CH_PD PullUp

Minimal Hardware Setup for Running only

ESPxx Hardware

PIN Resistor Power supply
VCC VCC (3.3V)
GND GND
GPIO0 PullUp
GPIO15 PullDown
CH_PD PullUp

Minimal

ESP min

Improved Stability

ESP improved stability

Boot Messages and Modes

The ESP module checks at every boot the Pins 0, 2 and 15. based on them its boots in different modes:

GPIO15 GPIO0 GPIO2 Mode
0V 0V 3.3V Uart Bootloader
0V 3.3V 3.3V Boot sketch (SPI flash)
3.3V x x SDIO mode (not used for Arduino)

at startup the ESP prints out the current boot mode example: rst cause:2, boot mode:(3,6)

note: - GPIO2 is used as TX output and the internal Pullup is enabled on boot.

rst cause

Number Description
0 unknown
1 normal boot
2 reset pin
3 software reset
4 watchdog reset

boot mode

the first value respects the pin setup of the Pins 0, 2 and 15.

Number GPIO15 GPIO0 GPIO2 Mode
0 0V 0V 0V Not valid
1 0V 0V 3.3V Uart
2 0V 3.3V 0V Not valid
3 0V 3.3V 3.3V Flash
4 3.3V 0V 0V SDIO
5 3.3V 0V 3.3V SDIO
6 3.3V 3.3V 0V SDIO
7 3.3V 3.3V 3.3V SDIO

note: - number = ((GPIO15 << 2) | (GPIO0 << 1) | GPIO2);

WeMos D1

Product page: http://wemos.cc

WeMos D1 mini

Product page: http://wemos.cc