Table of Contents

• Flash layout
• Uploading files to file system
• File system object (SPIFFS)
  • begin
  • format
  • open
  • exists
  • openDir
  • remove
  • rename
  • info
• Filesystem information structure
• Directory object (Dir)
• File object
  • seek
  • position
  • size
  • name
  • close

Flash layout

Even though file system is stored on the same flash chip as the program, programming new sketch will not modify file system contents. This allows to use file system to store sketch data, configuration files, or content for Web server.

The following diagram illustrates flash layout used in Arduino environment:

|--------------|-------|---------------|--|--|--|--|--|
^              ^       ^               ^     ^
Sketch    OTA update   File system   EEPROM  WiFi config (SDK)

File system size depends on the flash chip size. Depending on the board which is selected in IDE, you have the following options for flash size:

Note: to use any of file system functions in the sketch, add the following include to the sketch:

#include "FS.h"

Uploading files to file system

ESP8266FS is a tool which integrates into the Arduino IDE. It adds a menu item to Tools menu for uploading the contents of sketch data directory into ESP8266 flash file system.

• Download the tool: https://github.com/esp8266/arduino-esp8266fs-plugin/releases/download/0.2.0/ESP8266FS-0.2.0.zip.
• In your Arduino sketchbook directory, create tools directory if it doesn't exist yet
• Unpack the tool into tools directory (the path will look like <home_dir>/Arduino/tools/ESP8266FS/tool/esp8266fs.jar)
• Restart Arduino IDE
• Open a sketch (or create a new one and save it)
• Go to sketch directory (choose Sketch > Show Sketch Folder)
• Create a directory named data and any files you want in the file system there
• Make sure you have selected a board, port, and closed Serial Monitor
• Select Tools > ESP8266 Sketch Data Upload. This should start uploading the files into ESP8266 flash file system. When done, IDE status bar will display SPIFFS Image Uploaded message.

File system object (SPIFFS)

begin

SPIFFS.begin()

This method mounts SPIFFS file system. It must be called before any other FS APIs are used. Returns true if file system was mounted successfully, false otherwise.

format

SPIFFS.format()

Formats the file system. May be called either before or after calling begin. Returns true if formatting was successful.

open

SPIFFS.open(path, mode)

Opens a file. path should be an absolute path starting with a slash (e.g. /dir/filename.txt). mode is a string specifying access mode. It can be one of "r", "w", "a", "r+", "w+", "a+". Meaning of these modes is the same as for fopen C function.

Returns File object. To check whether the file was opened successfully, use the boolean operator.

File f = SPIFFS.open("/f.txt", "w");
if (!f) {
    Serial.println("file open failed");
}

exists

SPIFFS.exists(path)

Returns true if a file with given path exists, false otherwise.

openDir

SPIFFS.openDir(path)

Opens a directory given its absolute path. Returns a Dir object.

remove

SPIFFS.remove(path)

Deletes the file given its absolute path. Returns true if file was deleted successfully.

rename

SPIFFS.rename(pathFrom, pathTo)

Renames file from pathFrom to pathTo. Paths must be absolute. Returns true if file was renamed successfully.

info

FSInfo fs_info;
SPIFFS.info(fs_info);

Fills FSInfo structure with information about the file system. Returns true is successful, false otherwise.

Filesystem information structure

struct FSInfo {
    size_t totalBytes;
    size_t usedBytes;
    size_t blockSize;
    size_t pageSize;
    size_t maxOpenFiles;
    size_t maxPathLength;
};

This is the structure which may be filled using FS::info method. - totalBytes — total size of useful data on the file system - usedBytes — number of bytes used by files - blockSize — SPIFFS block size - pageSize — SPIFFS logical page size - maxOpenFiles — max number of files which may be open simultaneously - maxPathLength — max file name length (including one byte for zero termination)

Directory object (Dir)

The purpose of Dir object is to iterate over files inside a directory. It provides three methods: next(), fileName(), and openFile(mode).

The following example shows how it should be used:

Dir dir = SPIFFS.openDir("/data");
while (dir.next()) {
    Serial.print(dir.fileName());
    File f = dir.openFile("r");
    Serial.println(f.size());
}

dir.next() returns true while there are files in the directory to iterate over. It must be called before calling fileName and openFile functions.

openFile method takes mode argument which has the same meaning as for SPIFFS.open function.

File object

SPIFFS.open and dir.openFile functions return a File object. This object supports all the functions of Stream, so you can use readBytes, findUntil, parseInt, println, and all other Stream methods.

There are also some functions which are specific to File object.

seek

file.seek(offset, mode)

This function behaves like fseek C function. Depending on the value of mode, it moves current position in a file as follows:

• if mode is SeekSet, position is set to offset bytes from the beginning.
• if mode is SeekCur, current position is moved by offset bytes.
• if mode is SeekEnd, position is set to offset bytes from the end of the file.

Returns true if position was set successfully.

position

file.position()

Returns the current position inside the file, in bytes.

size

file.size()

Returns file size, in bytes.

name

String name = file.name();

Returns file name, as const char*. Convert it to String for storage.

close

file.close()

Close the file. No other operations should be performed on File object after close function was called.